Electrical Glossary & Home Safety Terms
Understanding electrical terminology can make it easier to identify potential problems, communicate with an electrician, plan electrical upgrades, and make informed decisions about your home or business.
This glossary from Shalkham Electric & Construction Co. explains common electrical terms, components, safety devices, wiring methods, service equipment, generators, EV charging systems, and solar equipment.
#
120/240V Service
A 120/240V service is the standard single-phase supply for most homes in North America. It delivers two 120-volt legs that combine to provide 240 volts, so lighting and general-purpose receptacles run at 120 volts while larger equipment such as ranges, dryers, and electric water heaters uses the 240-volt combination.
Related service: electrical service upgrades
200-Amp Service
A 200-amp service is an electrical service rated to carry up to 200 amperes, and it is a common size for modern homes. Whether a particular home needs this capacity is determined by a load calculation rather than by the rating alone, since the appropriate size depends on the connected equipment.
Related service: 200-amp electrical service
A
AC (Alternating Current)
Alternating current (AC) is an electrical current that periodically reverses direction. AC is the type of electricity commonly supplied by electric utilities and used throughout homes and businesses.
AFCI (Arc-Fault Circuit Interrupter)
An AFCI is a protective device designed to detect electrical arcing conditions that may create a fire hazard and interrupt the circuit when certain dangerous arc-fault conditions are detected.
Related service: electrical panel upgrade
Amperage (Amps)
Amperage, measured in amperes or amps (A), describes the amount of electrical current flowing through a conductor or circuit.
Ampere
An ampere, commonly shortened to amp, is the standard unit used to measure electrical current.
Arc Fault
An arc fault occurs when electricity unintentionally travels between conductors or across a damaged or loose connection. Arc faults can generate intense heat and may create a fire hazard.
Automatic Transfer Switch (ATS)
An automatic transfer switch automatically transfers a building's electrical load from utility power to a standby generator when an outage is detected and transfers it back when utility service returns.
Related service: standby generator
B
Backup Generator
A backup generator provides an alternative source of electricity when normal utility power is unavailable. Backup systems may be portable, manually connected, or permanently installed as standby generator systems.
Related service: backup generator
Ballast
A ballast is an electrical component used with certain fluorescent and HID lighting systems to regulate the current supplied to the lamp.
Related service: commercial and industrial lighting
Bonding
Electrical bonding connects conductive materials together to establish electrical continuity and help create an effective path for fault current.
Branch Circuit
A branch circuit is the portion of an electrical system extending from the final overcurrent protection device to outlets, lights, appliances, or other electrical loads.
Breaker Box
A breaker box is a common term for an electrical panel or load center containing circuit breakers that distribute electricity throughout a building.
C
Circuit
An electrical circuit is a complete conductive path through which electrical current can flow.
Circuit Breaker
A circuit breaker is an automatically operated protective device designed to interrupt electrical current when an overcurrent or certain fault condition occurs.
Related service: electrical troubleshooting and repairs
Circuit Overload
A circuit overload occurs when electrical demand exceeds the amount of current a circuit is designed to safely carry. Common warning signs include frequently tripping breakers, dimming or flickering lights, warm receptacles or switches, buzzing components, and burning odors.
Related service: electrical repairs
Conductor
A conductor is a material that allows electric current to flow. Copper and aluminum are commonly used electrical conductors.
Conduit
Electrical conduit is tubing or raceway used to route and protect electrical wires and cables. Depending on the application, conduit may be metallic or nonmetallic.
Continuity
Continuity describes an uninterrupted electrical path through which current can flow.
D
DC (Direct Current)
Direct current (DC) is electrical current that flows primarily in one direction. Batteries, solar photovoltaic systems, and many electronic devices use DC electricity.
Dedicated Circuit
A dedicated circuit supplies a specific appliance or piece of equipment rather than serving multiple general-purpose loads — commonly associated with electric ranges, dryers, HVAC equipment, sump pumps, EV chargers, hot tubs, and large appliances.
Related service: residential electrical services
Demand Load
Demand load is the portion of the total connected load expected to be drawing power at the same time. Because not every appliance and circuit operates simultaneously, demand load is normally lower than the connected load, and estimating it is the purpose of a load calculation when sizing a service or feeder.
Disconnect
An electrical disconnect is a device that allows electrical power to equipment, a circuit, or an entire service to be intentionally disconnected.
E
EGC (Equipment Grounding Conductor)
An equipment grounding conductor connects the metal enclosures and other non-current-carrying metal parts of equipment back to the system ground. It carries no current under normal conditions, and its purpose is to provide a low-impedance path that lets an overcurrent device operate if a fault energizes a metal part.
Electric Meter
An electric meter measures the amount of electrical energy consumed by a property for utility billing and monitoring purposes.
Electrical Code
An electrical code establishes requirements intended to promote safe electrical design and installation. Applicable requirements can vary by jurisdiction and by the code edition adopted locally.
Electrical Inspection
An electrical inspection evaluates electrical work or existing electrical components for compliance with applicable requirements and potential safety concerns.
Electrical Load
An electrical load is any device or equipment that consumes electrical power.
Electrical Panel
An electrical panel distributes incoming electrical power among the branch circuits serving a building. Most modern residential panels contain circuit breakers that provide overcurrent protection. Also called a breaker box, load center, or distribution panel.
Related service: electrical panel upgrades
Electrical Service
Electrical service generally refers to the conductors and equipment that deliver electricity from the utility supply point to a property's service equipment.
Related service: electrical service upgrades
Emergency Electrical Repair
Emergency electrical repair addresses electrical conditions that may create an immediate safety concern, significant loss of power, or risk of property damage — such as burning odors, sparking equipment, storm damage, or sudden power loss.
Related service: 24/7 emergency electrical service
EV Charger
An EV charger, also called electric vehicle supply equipment (EVSE), supplies electricity to an electric vehicle's onboard charging system.
Related service: EV charger installation
EVSE (Electric Vehicle Supply Equipment)
EVSE is the equipment used to safely deliver electrical energy from a building's electrical system to an electric vehicle.
F
Fault
An electrical fault is an abnormal condition that causes current to travel along an unintended path or creates abnormal current flow.
Feeder
A feeder consists of conductors that carry power from service equipment or another distribution source to downstream distribution equipment such as a subpanel.
Fuse
A fuse is an overcurrent protection device containing an element designed to open the circuit when current exceeds specified limits.
G
GEC (Grounding Electrode Conductor)
A grounding electrode conductor connects the grounding electrode system, such as a ground rod or metal underground water pipe, to the service equipment. It establishes the connection between the electrical system and the earth, and it is distinct from the equipment grounding conductor that bonds equipment enclosures.
GFCI (Ground-Fault Circuit Interrupter)
A GFCI is a protective device designed to interrupt power when it detects an imbalance in current consistent with current flowing along an unintended path. GFCI protection is common near moisture, where shock protection is especially important.
Related service: residential electrical services
Ground
In electrical systems, ground can refer to the earth or to conductive paths intentionally connected to earth or equipment grounding systems for safety and system operation.
Ground Fault
A ground fault occurs when electrical current takes an unintended conductive path toward ground or grounded components.
Ground Rod
A ground rod is a metal rod driven into the earth to serve as a grounding electrode. It is connected to the service equipment by a grounding electrode conductor, and it is one of several electrode types recognized for establishing a connection between an electrical system and the earth.
Grounding
Grounding connects parts of an electrical system to earth in a manner intended to support electrical safety and proper system operation.
Grounding Electrode
A grounding electrode is a conductive object through which an electrical system is connected to earth, such as certain ground rods.
Ground Wire
A ground wire is a common term for a grounding conductor used as part of an electrical grounding or equipment-grounding system.
H
High-Bay Lighting
High-bay lighting refers to fixtures designed for spaces with tall ceilings, typically warehouses, gymnasiums, and manufacturing floors. The fixtures and their optics are selected to deliver usable light at floor level from a substantial mounting height, which is why they differ from ordinary commercial fixtures.
Related service: commercial and industrial lighting
Hot Wire
A hot wire is an energized conductor that carries voltage from the electrical source toward a load.
Hot Tub Circuit
A hot tub circuit is an electrical circuit designed to supply a spa or hot tub, with specific requirements for circuit sizing, disconnecting means, grounding, bonding, and GFCI protection.
Related service: electrical installations
Hertz (Hz)
Hertz measures frequency in cycles per second. Standard utility power in the United States operates at 60 Hz.
I
Insulator
An insulator is a material that resists the flow of electrical current. Rubber, glass, porcelain, and certain plastics are commonly used for electrical insulation.
Inverter
An inverter converts direct current (DC) electricity into alternating current (AC), and is an important component in solar photovoltaic systems, battery systems, and certain backup-power applications.
J
Junction Box
A junction box is an enclosure used to contain and protect electrical connections, splices, and wiring.
K
Kilowatt (kW)
A kilowatt equals 1,000 watts and is commonly used to describe electrical power demand or equipment output.
Kilowatt-Hour (kWh)
A kilowatt-hour measures electrical energy consumption. One kilowatt-hour represents the energy used by a 1,000-watt load operating for one hour.
Knob-and-Tube Wiring
Knob-and-tube wiring is an older wiring method common in buildings from the late 19th to early 20th century, with conductors supported by porcelain knobs and tubes. Existing systems may warrant evaluation before renovations or major electrical upgrades.
Related service: whole-home rewiring
L
LED (Light-Emitting Diode)
An LED is a semiconductor light source widely used in modern residential, commercial, and industrial lighting because of its energy efficiency and long operating life.
Level 1 EV Charging
Level 1 EV charging typically uses a standard 120-volt AC source and generally provides slower vehicle charging than Level 2 equipment.
Level 2 EV Charging
Level 2 EV charging uses a higher-voltage AC circuit than Level 1 charging and can significantly increase charging speed for compatible electric vehicles.
Related service: EV charger installation
Load Calculation
An electrical load calculation is used to estimate the electrical demand of a building or system and determine appropriate service, feeder, and circuit capacity — particularly important when adding equipment like EV chargers, ranges, heat pumps, or hot tubs.
Related service: electrical panel upgrade
Load Center
A load center is an electrical distribution panel containing overcurrent protective devices that distribute power to branch circuits.
M
Main Breaker
The main breaker is a circuit breaker that can disconnect power supplied to downstream portions of an electrical distribution system and provides overcurrent protection according to its application.
Related service: electrical panel services
Meter Base
A meter base, also called a meter socket, is the enclosure designed to receive and electrically connect the utility's electric meter to the service conductors.
Related service: electrical service upgrades
Meter Socket
A meter socket is the enclosure that holds the utility's electric meter and connects it between the service conductors and the building's service equipment. Ownership and maintenance responsibilities for the meter socket and related service equipment can vary by utility and jurisdiction.
Related service: electrical service upgrades
Multimeter
A multimeter is a test instrument that measures several electrical values, most commonly voltage, current, and resistance. Electricians use one to verify that a circuit has been de-energized before work begins, to trace faults, and to confirm that a repair performs as intended.
N
National Electrical Code (NEC)
The National Electrical Code (NEC), also known as NFPA 70, is a widely adopted electrical installation standard published by the National Fire Protection Association. State and local jurisdictions determine which edition and amendments apply.
Neutral
A neutral conductor is a grounded circuit conductor that can carry current during normal operation in many AC electrical systems.
Nonmetallic-Sheathed Cable (NM Cable)
NM cable is a common wiring method used in residential construction, containing insulated conductors within a nonmetallic outer sheath.
O
Ohm
An ohm (Ω) is the standard unit used to measure electrical resistance.
Ohm's Law
Ohm's Law describes the relationship between voltage, current, and resistance: V = I × R, where V is Voltage, I is Current, and R is Resistance.
Outlet
In everyday conversation, outlet often refers to a receptacle. Technically, an outlet is a point on a wiring system where current is taken to supply utilization equipment.
Overcurrent
Overcurrent is electrical current exceeding the rated or allowable current for equipment or conductors. Overloads, short circuits, and ground faults can create overcurrent conditions.
Overhead Service
Overhead electrical service delivers utility electricity to a building using conductors installed above ground, typically between a utility pole and the property's service equipment.
Related service: electrical service upgrades
P
Panel Upgrade
An electrical panel upgrade generally involves replacing or modifying electrical distribution equipment to accommodate electrical capacity, equipment condition, system configuration, or project requirements.
Related service: electrical panel upgrades in Erie, PA
Photovoltaic (PV)
Photovoltaic, commonly abbreviated PV, refers to technology that converts sunlight directly into electricity. Solar panels are photovoltaic modules.
Portable Generator
A portable generator is a movable engine-driven generator used to provide temporary electrical power. Portable generators should never be operated inside a home, garage, or other enclosed area because of carbon monoxide hazards.
Power
Electrical power describes the rate at which electrical energy is transferred or consumed and is commonly measured in watts.
Q
Qualified Electrician
A qualified electrician is a person with the training, knowledge, skills, and applicable credentials required to perform electrical work within the requirements of their jurisdiction and scope of work.
R
Raceway
A raceway is an enclosed channel designed specifically to hold conductors or cables. Conduit, surface raceway, and wireway are all forms of raceway, and the enclosure protects the wiring inside it from physical damage while providing a defined path for future changes.
Receptacle
A receptacle is a contact device installed at an outlet for connecting an attachment plug. In everyday language, it is commonly called an electrical outlet.
Resistance
Electrical resistance describes opposition to the flow of electrical current and is measured in ohms.
Romex
Romex is a commonly recognized brand name often used conversationally to describe certain types of nonmetallic-sheathed electrical cable.
S
Service Drop
A service drop is the set of overhead conductors running from the utility's pole or distribution line to the point of attachment on a building. It is the overhead counterpart to an underground service lateral, and responsibility for it is normally divided between the utility and the property owner at a defined service point.
Service Entrance
The service entrance includes components associated with bringing utility-supplied electricity into a property's service equipment.
Related service: electrical service upgrades
Service Entrance Cable (SE Cable)
Service entrance cable is a cable assembly manufactured for the conductors that run between the service point, the meter, and the service equipment. It is made in types intended specifically for this use and for the exposure conditions of a service, rather than for general branch-circuit wiring.
Related service: electrical service upgrades
Service Entrance Conductors
Service entrance conductors are the conductors that run from the service drop or service lateral to the service disconnecting means. They are the final segment of supply wiring before a building's own overcurrent protection begins, which is why their sizing and protection are treated differently from branch circuits.
Related service: electrical service upgrades
Service Mast
A service mast is a raceway or structural assembly used with certain overhead electrical services to route and support service conductors above the building.
Related service: 24/7 emergency electrical service
Service Upgrade
An electrical service upgrade increases or modernizes components of a property's electrical service to accommodate capacity requirements, equipment condition, or other electrical needs.
Related service: electrical service upgrades
Short Circuit
A short circuit occurs when current flows through an unintended low-impedance path, potentially creating very high current that causes an overcurrent protective device to operate.
Related service: electrical troubleshooting and repair
Single-Phase Power
Single-phase power is an AC power configuration commonly used for residential electrical service in the United States.
Solar Inverter
A solar inverter converts the direct current produced by photovoltaic panels into the alternating current a building's electrical system uses. Depending on the design it may be a single central inverter, a string inverter serving a group of panels, or microinverters mounted at each panel.
Solar Panel
A solar panel, or photovoltaic module, contains photovoltaic cells that convert sunlight into DC electricity.
SPD (Surge Protective Device)
A surge protective device limits transient overvoltages by diverting surge current away from connected equipment. SPDs are made in several types for different points in a system, from the service equipment down to individual receptacles, and they are the component underlying whole-house surge protection.
Related service: whole-building surge protection
Standby Generator
A standby generator is a permanently installed backup generator designed to provide power during utility outages, often working with an automatic transfer switch to start automatically.
Related service: home standby generator installation
Subpanel
A subpanel is a downstream electrical distribution panel supplied from another panel or service equipment, often used for additions, garages, workshops, or outbuildings.
Related service: electrical installations
Surge Protector
A surge protector is a device that limits transient overvoltage reaching the equipment plugged into it. Point-of-use protectors are the most familiar form, including plug-in strips and single-outlet adapters, though not every power strip provides surge protection — many are only multi-outlet extensions with no protective components inside. Point-of-use protection guards individual devices and does not protect the rest of the building, so it is generally used alongside, not instead of, whole-house surge protection installed at the electrical panel.
Related service: whole-building surge protection
T
Three-Phase Power
Three-phase power is an AC electrical configuration commonly used in commercial and industrial facilities because it can efficiently supply large electrical loads and motors.
Related service: commercial electrical services
Transformer
A transformer transfers electrical energy between circuits through electromagnetic induction and is commonly used to increase or decrease AC voltage.
Transfer Switch
A transfer switch transfers electrical loads between two power sources, such as utility service and a generator.
Related service: standby generator installation
Tripped Breaker
A tripped breaker is a circuit breaker that has opened the circuit after detecting a condition requiring interruption or because it was manually operated. Repeated trips should be investigated, not just reset.
Related service: electrical repairs and troubleshooting
U
Underground Service
Underground electrical service supplies utility power through conductors installed below ground rather than overhead.
Related service: electrical service upgrades
Uninterruptible Power Supply (UPS)
A UPS provides short-term backup electricity to connected equipment when normal power is interrupted and may also provide certain power-conditioning functions.
V
Volt
A volt (V) is the standard unit used to measure electrical potential difference.
Voltage Drop
Voltage drop is a reduction in voltage along conductors as current travels through an electrical circuit. Excessive voltage drop can negatively affect equipment performance.
W
Watt
A watt (W) is the standard unit of electrical power.
Weatherhead
A weatherhead is the weatherproof fitting at the top of a service mast or conduit where overhead service conductors enter the raceway. Its downward-facing opening, combined with drip loops in the conductors, is arranged so that water runs off rather than travelling down into the raceway. Storm damage to a mast or weatherhead is a common cause of an interrupted overhead service.
Related service: emergency electrical service
Whole-House Generator
A whole-house generator is a permanently installed standby generator designed to supply a substantial portion or, depending on system sizing and design, most or all of a home's electrical loads. It works with a transfer switch, which disconnects the utility supply and transfers the selected loads to generator power when an outage occurs.
Related service: whole-home standby generator installation
Whole-House Surge Protection
Whole-house surge protection generally refers to surge protective equipment installed at or near electrical distribution equipment to help protect circuits and connected devices from transient overvoltage events.
Related service: surge protection solutions
Wire Gauge
Wire gauge refers to conductor size. In the United States, many electrical conductors are identified using American Wire Gauge (AWG) sizes.
X
XHHW
XHHW is a designation used for certain insulated electrical conductors designed for specified applications and environmental conditions.
Y
Y-Connection (Wye)
A wye connection, sometimes represented by the letter Y, is a three-phase electrical configuration in which three phases connect to a common neutral point.
Z
Zero-Energy State
A zero-energy state describes a condition in which hazardous energy sources have been isolated and stored energy has been controlled or dissipated before certain work is performed.
Common Electrical Warning Signs
Understanding terminology is useful, but recognizing the signs of a potentially unsafe electrical condition is even more important. Contact a qualified electrician if you notice:
- Circuit breakers repeatedly tripping
- Fuses repeatedly blowing
- Burning or unusual electrical odors
- Sparking from receptacles, switches, or panels
- Warm or discolored receptacles and switches
- Buzzing or crackling from electrical equipment
- Frequently flickering lights
- Loose electrical receptacles
- Visible damaged or exposed wiring
- Electrical shocks or tingling from equipment
- Storm-damaged electrical service equipment
- A sudden partial loss of electrical power
Frequently Asked Electrical Questions
Straight answers to common questions about electrical terminology, safety, and service from Shalkham Electric & Construction Co.
Have an Electrical Question or Need Service?
Whether you're dealing with a breaker that keeps tripping, planning an electrical panel upgrade, installing an EV charger, adding a generator, or troubleshooting an electrical problem, Shalkham Electric & Construction Co. can help evaluate your system and recommend the right solution.
Call us 24/7 at (814) 873-2788 or send us your question below.
Our electrical services include:
- Electrical troubleshooting & repair
- Emergency electrical services
- Panel & service upgrades
- EV charger installation
- Generator installation & service
- Residential, commercial & industrial wiring
Ask a Question
We'll get back to you within 1 business hour.
Need an Electrician You Can Trust?
Licensed, insured, and available 24/7 across Erie, Crawford & Warren Counties PA, Ashtabula County OH, and Chautauqua County NY.