Call Now Get Estimate
Call 24/7(814) 873-2788

Electrical Glossary & Home Safety Terms

Understanding electrical terminology can make it easier to identify potential problems, communicate with an electrician, plan electrical upgrades, and make informed decisions about your home or business.

This glossary from Shalkham Electric & Construction Co. explains common electrical terms, components, safety devices, wiring methods, service equipment, generators, EV charging systems, and solar equipment.

#

120/240V Service

A 120/240V service is the standard single-phase supply for most homes in North America. It delivers two 120-volt legs that combine to provide 240 volts, so lighting and general-purpose receptacles run at 120 volts while larger equipment such as ranges, dryers, and electric water heaters uses the 240-volt combination.

200-Amp Service

A 200-amp service is an electrical service rated to carry up to 200 amperes, and it is a common size for modern homes. Whether a particular home needs this capacity is determined by a load calculation rather than by the rating alone, since the appropriate size depends on the connected equipment.

A

AC (Alternating Current)

Alternating current (AC) is an electrical current that periodically reverses direction. AC is the type of electricity commonly supplied by electric utilities and used throughout homes and businesses.

AFCI (Arc-Fault Circuit Interrupter)

An AFCI is a protective device designed to detect electrical arcing conditions that may create a fire hazard and interrupt the circuit when certain dangerous arc-fault conditions are detected.

Amperage (Amps)

Amperage, measured in amperes or amps (A), describes the amount of electrical current flowing through a conductor or circuit.

Ampere

An ampere, commonly shortened to amp, is the standard unit used to measure electrical current.

Arc Fault

An arc fault occurs when electricity unintentionally travels between conductors or across a damaged or loose connection. Arc faults can generate intense heat and may create a fire hazard.

Automatic Transfer Switch (ATS)

An automatic transfer switch automatically transfers a building's electrical load from utility power to a standby generator when an outage is detected and transfers it back when utility service returns.

B

Backup Generator

A backup generator provides an alternative source of electricity when normal utility power is unavailable. Backup systems may be portable, manually connected, or permanently installed as standby generator systems.

Ballast

A ballast is an electrical component used with certain fluorescent and HID lighting systems to regulate the current supplied to the lamp.

Bonding

Electrical bonding connects conductive materials together to establish electrical continuity and help create an effective path for fault current.

Branch Circuit

A branch circuit is the portion of an electrical system extending from the final overcurrent protection device to outlets, lights, appliances, or other electrical loads.

Breaker Box

A breaker box is a common term for an electrical panel or load center containing circuit breakers that distribute electricity throughout a building.

C

Circuit

An electrical circuit is a complete conductive path through which electrical current can flow.

Circuit Breaker

A circuit breaker is an automatically operated protective device designed to interrupt electrical current when an overcurrent or certain fault condition occurs.

Circuit Overload

A circuit overload occurs when electrical demand exceeds the amount of current a circuit is designed to safely carry. Common warning signs include frequently tripping breakers, dimming or flickering lights, warm receptacles or switches, buzzing components, and burning odors.

Conductor

A conductor is a material that allows electric current to flow. Copper and aluminum are commonly used electrical conductors.

Conduit

Electrical conduit is tubing or raceway used to route and protect electrical wires and cables. Depending on the application, conduit may be metallic or nonmetallic.

Continuity

Continuity describes an uninterrupted electrical path through which current can flow.

D

DC (Direct Current)

Direct current (DC) is electrical current that flows primarily in one direction. Batteries, solar photovoltaic systems, and many electronic devices use DC electricity.

Dedicated Circuit

A dedicated circuit supplies a specific appliance or piece of equipment rather than serving multiple general-purpose loads — commonly associated with electric ranges, dryers, HVAC equipment, sump pumps, EV chargers, hot tubs, and large appliances.

Demand Load

Demand load is the portion of the total connected load expected to be drawing power at the same time. Because not every appliance and circuit operates simultaneously, demand load is normally lower than the connected load, and estimating it is the purpose of a load calculation when sizing a service or feeder.

Disconnect

An electrical disconnect is a device that allows electrical power to equipment, a circuit, or an entire service to be intentionally disconnected.

E

EGC (Equipment Grounding Conductor)

An equipment grounding conductor connects the metal enclosures and other non-current-carrying metal parts of equipment back to the system ground. It carries no current under normal conditions, and its purpose is to provide a low-impedance path that lets an overcurrent device operate if a fault energizes a metal part.

Electric Meter

An electric meter measures the amount of electrical energy consumed by a property for utility billing and monitoring purposes.

Electrical Code

An electrical code establishes requirements intended to promote safe electrical design and installation. Applicable requirements can vary by jurisdiction and by the code edition adopted locally.

Electrical Inspection

An electrical inspection evaluates electrical work or existing electrical components for compliance with applicable requirements and potential safety concerns.

Electrical Load

An electrical load is any device or equipment that consumes electrical power.

Electrical Panel

An electrical panel distributes incoming electrical power among the branch circuits serving a building. Most modern residential panels contain circuit breakers that provide overcurrent protection. Also called a breaker box, load center, or distribution panel.

Electrical Service

Electrical service generally refers to the conductors and equipment that deliver electricity from the utility supply point to a property's service equipment.

Emergency Electrical Repair

Emergency electrical repair addresses electrical conditions that may create an immediate safety concern, significant loss of power, or risk of property damage — such as burning odors, sparking equipment, storm damage, or sudden power loss.

EV Charger

An EV charger, also called electric vehicle supply equipment (EVSE), supplies electricity to an electric vehicle's onboard charging system.

EVSE (Electric Vehicle Supply Equipment)

EVSE is the equipment used to safely deliver electrical energy from a building's electrical system to an electric vehicle.

F

Fault

An electrical fault is an abnormal condition that causes current to travel along an unintended path or creates abnormal current flow.

Feeder

A feeder consists of conductors that carry power from service equipment or another distribution source to downstream distribution equipment such as a subpanel.

Fuse

A fuse is an overcurrent protection device containing an element designed to open the circuit when current exceeds specified limits.

G

GEC (Grounding Electrode Conductor)

A grounding electrode conductor connects the grounding electrode system, such as a ground rod or metal underground water pipe, to the service equipment. It establishes the connection between the electrical system and the earth, and it is distinct from the equipment grounding conductor that bonds equipment enclosures.

GFCI (Ground-Fault Circuit Interrupter)

A GFCI is a protective device designed to interrupt power when it detects an imbalance in current consistent with current flowing along an unintended path. GFCI protection is common near moisture, where shock protection is especially important.

Ground

In electrical systems, ground can refer to the earth or to conductive paths intentionally connected to earth or equipment grounding systems for safety and system operation.

Ground Fault

A ground fault occurs when electrical current takes an unintended conductive path toward ground or grounded components.

Ground Rod

A ground rod is a metal rod driven into the earth to serve as a grounding electrode. It is connected to the service equipment by a grounding electrode conductor, and it is one of several electrode types recognized for establishing a connection between an electrical system and the earth.

Grounding

Grounding connects parts of an electrical system to earth in a manner intended to support electrical safety and proper system operation.

Grounding Electrode

A grounding electrode is a conductive object through which an electrical system is connected to earth, such as certain ground rods.

Ground Wire

A ground wire is a common term for a grounding conductor used as part of an electrical grounding or equipment-grounding system.

H

High-Bay Lighting

High-bay lighting refers to fixtures designed for spaces with tall ceilings, typically warehouses, gymnasiums, and manufacturing floors. The fixtures and their optics are selected to deliver usable light at floor level from a substantial mounting height, which is why they differ from ordinary commercial fixtures.

Hot Wire

A hot wire is an energized conductor that carries voltage from the electrical source toward a load.

Hot Tub Circuit

A hot tub circuit is an electrical circuit designed to supply a spa or hot tub, with specific requirements for circuit sizing, disconnecting means, grounding, bonding, and GFCI protection.

Hertz (Hz)

Hertz measures frequency in cycles per second. Standard utility power in the United States operates at 60 Hz.

I

Insulator

An insulator is a material that resists the flow of electrical current. Rubber, glass, porcelain, and certain plastics are commonly used for electrical insulation.

Inverter

An inverter converts direct current (DC) electricity into alternating current (AC), and is an important component in solar photovoltaic systems, battery systems, and certain backup-power applications.

J

Junction Box

A junction box is an enclosure used to contain and protect electrical connections, splices, and wiring.

K

Kilowatt (kW)

A kilowatt equals 1,000 watts and is commonly used to describe electrical power demand or equipment output.

Kilowatt-Hour (kWh)

A kilowatt-hour measures electrical energy consumption. One kilowatt-hour represents the energy used by a 1,000-watt load operating for one hour.

Knob-and-Tube Wiring

Knob-and-tube wiring is an older wiring method common in buildings from the late 19th to early 20th century, with conductors supported by porcelain knobs and tubes. Existing systems may warrant evaluation before renovations or major electrical upgrades.

L

LED (Light-Emitting Diode)

An LED is a semiconductor light source widely used in modern residential, commercial, and industrial lighting because of its energy efficiency and long operating life.

Level 1 EV Charging

Level 1 EV charging typically uses a standard 120-volt AC source and generally provides slower vehicle charging than Level 2 equipment.

Level 2 EV Charging

Level 2 EV charging uses a higher-voltage AC circuit than Level 1 charging and can significantly increase charging speed for compatible electric vehicles.

Load Calculation

An electrical load calculation is used to estimate the electrical demand of a building or system and determine appropriate service, feeder, and circuit capacity — particularly important when adding equipment like EV chargers, ranges, heat pumps, or hot tubs.

Load Center

A load center is an electrical distribution panel containing overcurrent protective devices that distribute power to branch circuits.

M

Main Breaker

The main breaker is a circuit breaker that can disconnect power supplied to downstream portions of an electrical distribution system and provides overcurrent protection according to its application.

Meter Base

A meter base, also called a meter socket, is the enclosure designed to receive and electrically connect the utility's electric meter to the service conductors.

Meter Socket

A meter socket is the enclosure that holds the utility's electric meter and connects it between the service conductors and the building's service equipment. Ownership and maintenance responsibilities for the meter socket and related service equipment can vary by utility and jurisdiction.

Multimeter

A multimeter is a test instrument that measures several electrical values, most commonly voltage, current, and resistance. Electricians use one to verify that a circuit has been de-energized before work begins, to trace faults, and to confirm that a repair performs as intended.

N

National Electrical Code (NEC)

The National Electrical Code (NEC), also known as NFPA 70, is a widely adopted electrical installation standard published by the National Fire Protection Association. State and local jurisdictions determine which edition and amendments apply.

Neutral

A neutral conductor is a grounded circuit conductor that can carry current during normal operation in many AC electrical systems.

Nonmetallic-Sheathed Cable (NM Cable)

NM cable is a common wiring method used in residential construction, containing insulated conductors within a nonmetallic outer sheath.

O

Ohm

An ohm (Ω) is the standard unit used to measure electrical resistance.

Ohm's Law

Ohm's Law describes the relationship between voltage, current, and resistance: V = I × R, where V is Voltage, I is Current, and R is Resistance.

Outlet

In everyday conversation, outlet often refers to a receptacle. Technically, an outlet is a point on a wiring system where current is taken to supply utilization equipment.

Overcurrent

Overcurrent is electrical current exceeding the rated or allowable current for equipment or conductors. Overloads, short circuits, and ground faults can create overcurrent conditions.

Overhead Service

Overhead electrical service delivers utility electricity to a building using conductors installed above ground, typically between a utility pole and the property's service equipment.

P

Panel Upgrade

An electrical panel upgrade generally involves replacing or modifying electrical distribution equipment to accommodate electrical capacity, equipment condition, system configuration, or project requirements.

Photovoltaic (PV)

Photovoltaic, commonly abbreviated PV, refers to technology that converts sunlight directly into electricity. Solar panels are photovoltaic modules.

Portable Generator

A portable generator is a movable engine-driven generator used to provide temporary electrical power. Portable generators should never be operated inside a home, garage, or other enclosed area because of carbon monoxide hazards.

Power

Electrical power describes the rate at which electrical energy is transferred or consumed and is commonly measured in watts.

Q

Qualified Electrician

A qualified electrician is a person with the training, knowledge, skills, and applicable credentials required to perform electrical work within the requirements of their jurisdiction and scope of work.

R

Raceway

A raceway is an enclosed channel designed specifically to hold conductors or cables. Conduit, surface raceway, and wireway are all forms of raceway, and the enclosure protects the wiring inside it from physical damage while providing a defined path for future changes.

Receptacle

A receptacle is a contact device installed at an outlet for connecting an attachment plug. In everyday language, it is commonly called an electrical outlet.

Resistance

Electrical resistance describes opposition to the flow of electrical current and is measured in ohms.

Romex

Romex is a commonly recognized brand name often used conversationally to describe certain types of nonmetallic-sheathed electrical cable.

S

Service Drop

A service drop is the set of overhead conductors running from the utility's pole or distribution line to the point of attachment on a building. It is the overhead counterpart to an underground service lateral, and responsibility for it is normally divided between the utility and the property owner at a defined service point.

Service Entrance

The service entrance includes components associated with bringing utility-supplied electricity into a property's service equipment.

Service Entrance Cable (SE Cable)

Service entrance cable is a cable assembly manufactured for the conductors that run between the service point, the meter, and the service equipment. It is made in types intended specifically for this use and for the exposure conditions of a service, rather than for general branch-circuit wiring.

Service Entrance Conductors

Service entrance conductors are the conductors that run from the service drop or service lateral to the service disconnecting means. They are the final segment of supply wiring before a building's own overcurrent protection begins, which is why their sizing and protection are treated differently from branch circuits.

Service Mast

A service mast is a raceway or structural assembly used with certain overhead electrical services to route and support service conductors above the building.

Service Upgrade

An electrical service upgrade increases or modernizes components of a property's electrical service to accommodate capacity requirements, equipment condition, or other electrical needs.

Short Circuit

A short circuit occurs when current flows through an unintended low-impedance path, potentially creating very high current that causes an overcurrent protective device to operate.

Single-Phase Power

Single-phase power is an AC power configuration commonly used for residential electrical service in the United States.

Solar Inverter

A solar inverter converts the direct current produced by photovoltaic panels into the alternating current a building's electrical system uses. Depending on the design it may be a single central inverter, a string inverter serving a group of panels, or microinverters mounted at each panel.

Solar Panel

A solar panel, or photovoltaic module, contains photovoltaic cells that convert sunlight into DC electricity.

SPD (Surge Protective Device)

A surge protective device limits transient overvoltages by diverting surge current away from connected equipment. SPDs are made in several types for different points in a system, from the service equipment down to individual receptacles, and they are the component underlying whole-house surge protection.

Standby Generator

A standby generator is a permanently installed backup generator designed to provide power during utility outages, often working with an automatic transfer switch to start automatically.

Subpanel

A subpanel is a downstream electrical distribution panel supplied from another panel or service equipment, often used for additions, garages, workshops, or outbuildings.

Surge Protector

A surge protector is a device that limits transient overvoltage reaching the equipment plugged into it. Point-of-use protectors are the most familiar form, including plug-in strips and single-outlet adapters, though not every power strip provides surge protection — many are only multi-outlet extensions with no protective components inside. Point-of-use protection guards individual devices and does not protect the rest of the building, so it is generally used alongside, not instead of, whole-house surge protection installed at the electrical panel.

T

Three-Phase Power

Three-phase power is an AC electrical configuration commonly used in commercial and industrial facilities because it can efficiently supply large electrical loads and motors.

Transformer

A transformer transfers electrical energy between circuits through electromagnetic induction and is commonly used to increase or decrease AC voltage.

Transfer Switch

A transfer switch transfers electrical loads between two power sources, such as utility service and a generator.

Tripped Breaker

A tripped breaker is a circuit breaker that has opened the circuit after detecting a condition requiring interruption or because it was manually operated. Repeated trips should be investigated, not just reset.

U

Underground Service

Underground electrical service supplies utility power through conductors installed below ground rather than overhead.

Uninterruptible Power Supply (UPS)

A UPS provides short-term backup electricity to connected equipment when normal power is interrupted and may also provide certain power-conditioning functions.

V

Volt

A volt (V) is the standard unit used to measure electrical potential difference.

Voltage Drop

Voltage drop is a reduction in voltage along conductors as current travels through an electrical circuit. Excessive voltage drop can negatively affect equipment performance.

W

Watt

A watt (W) is the standard unit of electrical power.

Weatherhead

A weatherhead is the weatherproof fitting at the top of a service mast or conduit where overhead service conductors enter the raceway. Its downward-facing opening, combined with drip loops in the conductors, is arranged so that water runs off rather than travelling down into the raceway. Storm damage to a mast or weatherhead is a common cause of an interrupted overhead service.

Whole-House Generator

A whole-house generator is a permanently installed standby generator designed to supply a substantial portion or, depending on system sizing and design, most or all of a home's electrical loads. It works with a transfer switch, which disconnects the utility supply and transfers the selected loads to generator power when an outage occurs.

Whole-House Surge Protection

Whole-house surge protection generally refers to surge protective equipment installed at or near electrical distribution equipment to help protect circuits and connected devices from transient overvoltage events.

Wire Gauge

Wire gauge refers to conductor size. In the United States, many electrical conductors are identified using American Wire Gauge (AWG) sizes.

X

XHHW

XHHW is a designation used for certain insulated electrical conductors designed for specified applications and environmental conditions.

Y

Y-Connection (Wye)

A wye connection, sometimes represented by the letter Y, is a three-phase electrical configuration in which three phases connect to a common neutral point.

Z

Zero-Energy State

A zero-energy state describes a condition in which hazardous energy sources have been isolated and stored energy has been controlled or dissipated before certain work is performed.

Common Electrical Warning Signs

Understanding terminology is useful, but recognizing the signs of a potentially unsafe electrical condition is even more important. Contact a qualified electrician if you notice:

  • Circuit breakers repeatedly tripping
  • Fuses repeatedly blowing
  • Burning or unusual electrical odors
  • Sparking from receptacles, switches, or panels
  • Warm or discolored receptacles and switches
  • Buzzing or crackling from electrical equipment
  • Frequently flickering lights
  • Loose electrical receptacles
  • Visible damaged or exposed wiring
  • Electrical shocks or tingling from equipment
  • Storm-damaged electrical service equipment
  • A sudden partial loss of electrical power
Do not touch exposed conductors, damaged service equipment, or downed electrical lines. If there is an immediate fire, electrocution, or life-safety emergency, move to a safe location and contact emergency services.
Common Questions

Frequently Asked Electrical Questions

Straight answers to common questions about electrical terminology, safety, and service from Shalkham Electric & Construction Co.

Both provide overcurrent protection. A fuse contains an element that opens the circuit when excessive current causes it to operate and must then be replaced. A circuit breaker opens the circuit under specified conditions and can generally be reset after the underlying problem has been identified and corrected.
A circuit breaker may repeatedly trip because of an overloaded circuit, short circuit, ground fault, arc-fault condition, defective equipment, or a wiring problem. Recurring trips should be investigated by a licensed electrician rather than continually resetting the breaker.
A GFCI is primarily intended to reduce the risk of electric shock from certain ground-fault conditions. An AFCI is intended to detect dangerous arcing conditions that can contribute to electrical fires. Some devices provide both types of protection.
A 200-amp service is an electrical service designed around equipment and conductors with specified current ratings and capacity. Whether a property requires 100-, 150-, 200-amp, or another service configuration depends on the electrical load and applicable requirements.
Not necessarily. An electrician can evaluate the existing electrical service, panel capacity, available breaker space, charging equipment, and calculated electrical load to determine whether the existing system can accommodate the charger or whether additional work is required.
A portable generator is movable and typically requires manual setup and operation. A standby generator is permanently installed and can be configured with an automatic transfer switch to supply power automatically during a utility outage.
A dedicated circuit supplies a specific appliance or piece of equipment rather than multiple general-purpose loads. Dedicated circuits are frequently used for equipment with substantial or specialized electrical requirements.
Grounding generally connects an electrical system to earth. Bonding establishes electrical continuity between conductive components. The two work together as important parts of an electrical safety system but serve different purposes.

Have an Electrical Question or Need Service?

Whether you're dealing with a breaker that keeps tripping, planning an electrical panel upgrade, installing an EV charger, adding a generator, or troubleshooting an electrical problem, Shalkham Electric & Construction Co. can help evaluate your system and recommend the right solution.

Call us 24/7 at (814) 873-2788 or send us your question below.

Our electrical services include:

  • Electrical troubleshooting & repair
  • Emergency electrical services
  • Panel & service upgrades
  • EV charger installation
  • Generator installation & service
  • Residential, commercial & industrial wiring

Ask a Question

We'll get back to you within 1 business hour.

Need an Electrician You Can Trust?

Licensed, insured, and available 24/7 across Erie, Crawford & Warren Counties PA, Ashtabula County OH, and Chautauqua County NY.

Scroll to Top